Engel Vertical ELAST 440 Ton 1500 CCM with CC 200 Control - Elast 1500/440 V Compact US
Engel Elast 1500/440 V Compact US
Age: 2009
Stock Number: 3406
Never in production - less than 1,000 hrs - under power
Click to view larger photo
Specification
Description
Clamp Force:
440 US Tons
Inj Volume:
1500 CCM
Inj Plunger Dia:
86 mm
Screw Dia:
40 mm
Screw L/D:
10/1
Heating Platen Size:
27.95" x 36.22"
Tie Bar Spacing:
19.68" x 32.28"
Max Daylight:
20.05"
Min Mold Ht:
9.84"
Clamp Stroke:
23.62"
Ejector Stroke:
11.81
Shuttle Table Stroke:
23.22"
Voltage:
480 V
Dimensions Press:
9144.09"" L x 55.71""W x 148"H
Weight Press:
39,242 lbs
Cost new:
$458,580.00
Equipped With:
Injection unit:
Vertical inj unit with fixed nozzle, inj from the top.
Equipped as standard with:
- preparation for 2 temperature units for the in unit
- injection nozzle temperat individually controlled
- intake block cooling with flow controller
- automatic rubber strip feeder
- additional operator pannel for strip feeding
- decompression prior and/or after plasticizing
- freely selectable profiles for plasticizing, back, injection and holding pressure
Clamp unit:
Automatic mold height adjustment.
2 heating zones per platen and function control
Hyd operated side ejector at fixed machine plate
Ejector bars with T-slots and stroke control
Hyd operated side ejector at movable machine plate
Quick mold clamp system, hydraulically operated,
Sliding plate/demolding table, hydraulically operated
2-Hand start button
KO station underneath sliding/shuttle table, per side
Hydraulic valve gate control 4-circuit
Energy efficient, low noise"Smart/Pump"
Automatic temperature control, automatic pre-heating and alarms for "Low
oil level" and "Temperature out of range".
Hydraulic package HV 1 with a single pump for
sequential machine motions
Electrics:
Control cabinet integrated in machine
-service outlet 2-pins, 230V/16A
-2 energy outlets 460V/16A, for temp units with weektimer
-1 energy outlet 460V/16A, for vacuum pump,
switched with pump motor
-switch for machine cycle without dosing
-20mA interface for temp units
Incoming voltage 3X460V+PE/60HZ
Service receptacle - 115 volts (2 amps maximum)
4 control circuit for mold heaters on fixed plate
incl. thyristor, plug and wiring (wiring according
16 Amp fuses
4 control circuit for mold heaters on moving plate
incl. thyristor, plug and wiring
Supplemental heaters for pre-heat station:
2 control circuit for mold heaters 3-phase
thyristors, plug and wiring
- Euromap interface located in rear of control
cabinet for connection to pre-heat station
Additional electronic board for 8 additional
Transformer for mold heat zones at 230V
1 - 8 zones Control:
EC200 A01 control package including:
- 12" TFT-color Touch Screen
- USB-memory for data storage
- User access via password
- Ethernet network interface
- Freely programmable cycle sequence with
graphical programming
- Micrograph
- Microplast
- PD-Record
- week timer for temperature control units
- strip feed monitoring via plunger retraction
- program for coining, venting and vacuum
Screen text English: EN
Program "virt mould" for viewing and revising
of parameter settings and for process optimization
on PC incl. simulation
Access rights with keycard
Machine support pads
Vacuum device, complete incl. vacuum valve and
pump with 40 m3/h capacity
Connection for air gun on operator side
Bilingual English/Spanish: BE
Additional preparation for mold change system to
include:
- 2x hydraulic manifold with valve
- Special bolt pattern bottom platen for mounting
- Electrical and software interface
Mold change system
- Hydraulic operated
- Pre-heat Station - heating from the bottom only
- Safety fences and access door on rear
- Bottom heating platen in special execution
with magnetic heating surface
- Top heating platen with modified spigots clamp system
25422 Trabuco Road, Ste 105 - 531
Lake Forest, CA 92630-2796
Phone: 949-756-8387
Fax: 949-263-1087 sales@pmexchange.com
